Restoring Track Car 7


The Rochester & Genesee Valley Railroad Museum rosters several different track cars including this little Fairmont MT-19. It has recently had a new engine installed and has been completely rewired. Once the better weather returns to Industry, the car will be given a complete cosmetic restoration and place into service on the museum's demonstration railroad.

Workin' on the Vulcan, ex-Brooklyn Navy Yard #12


The Rochester & Genesee Valley Railroad Museum rosters two 0-4-0 steam locomotives. The museum is currently working on both engines. The fireless Heisler is being restored both mechanically and cosmetically for service. Our Vulcan is currently undergoing a cosmetic restoration while the museum raises the funds to repair or build a new boiler for the engine. Here we see the pilot beam of the Vulcan, Brooklyn Navy Yard #12, being disassembled so the wood can be replaced.


The #12's pilot beam is a sandwich of steel plates and large wood beams. Here we see the large wood beams exposed. There are two beams that make up the pilot, and they are badly rotted. The beams are approximately 9.5" square and stacked one on the top of the other. Currently, the museum is planning to replace these large wooden beams with railroad switch timbers. We will need to use three timbers to replace the current two timbers.

Workin' on the Plymouth BL


Volunteers from the Rochester & Genesee Valley Railroad Museum continue the rebuild and restoration of our Plymouth BL gas mechanical locomotive. Work continued on the new thrust bearings for its axles. Here the material is being cut on our horizontal bandsaw for the bearings for the front axle.


Here is one of the bearings after the surfaces have been machined flat. Since we will not be removing the wheels, this bearing with be cut in half and set screws installed so the bearing can be split in half, placed around the axle and held back together with the set screws.


The bearings have already been installed on the engine's rear axle as seen here looking down on the top of the wheel. These bearings help to prevent the axles from shifting from side to side.


More progress on the Plymouth can also be seen with the installation of the first of several drive chains. The original chains were frozen solid with rust so new roller chain had to be purchased.


In order to service each axle, the front of the BL has been jacked up and the axle dropped out. New pedestal liners have been installed.


Looking from the inside, it is possible to see the new pedestal liners again. The axle bearings have also been rebuilt.


Along with all of the running gear work, the rack that is used to move the friction drive wheel has been completely rebuilt. This work included machining a brand new main shaft with all of the keyways machined into the shaft so the gears would work properly.

Work contines on Brooklyn Navy Yard No. 12


The Rochester & Genesee Valley Railroad Museum rosters two 0-4-0 steam locomotives. The museum is currently working on both engines. The fireless Heisler is being restored both mechanically and cosmetically for service. Our Vulcan, formerly Brooklyn Navy Yard #12, is currently undergoing a cosmetic restoration while the museum raises the funds to repair or build a new boiler for the engine. Here we see the pilot beam of the Vulcan being disassembled so the wood can be replaced.


The pilot beam is a sandwich of steel plates and large wood beams. Here we see the large wood beams exposed. There are two beams that make up the pilot, and they are badly rotted. The beams are approximately 9.5" square and stacked one on the top of the other. Currently, the Museum is planning to replace these large wooden beams with railroad switch timbers. We will need to use three timbers to replace the current two timbers.

Worling on our Plymouth BL


Our historic Plymouth BL gas-mechanical locomotive continues to receive new thrust bearings on its axles. Here the material is being cut on our horizontal bandsaw for the bearings for the front axle.


Here is one of the bearings after the surfaces have been machined flat. Since we will not be removing the wheels, this bearing with be cut in half and set screws installed so the bearing can be split in half, placed around the axle and held back together with the set screws.


The bearings have already been installed on the engine's rear axle as seen here looking down on the top of the wheel. These bearings help to prevent the axles from shifting from side to side.


More progress on the Plymouth can also be seen with the installation of the first of several drive chains. The original chains were frozen solid with rust so new roller chain had to be purchased.


In order to service each axle, the front of the BL has been jacked up and the axle dropped out. New pedestal liners have been installed.


Looking from the inside, it is possible to see the new pedestal liners again. The axle bearings have also been rebuilt.


Along with all of the running gear work, the rack that is used to move the friction drive wheel has been completely rebuilt. This work included machining a brand new main shaft with all of the keyways machined into the shaft so the gears would work properly.

Restoring Track Car 7


The Rochester & Genesee Valley Railroad Museum rosters several different track cars including this little Fairmont MT-19, designated TC-7. It has recently had a new engine installed and has been completely rewired. Once the better weather returns to Industry, the car will be given a complete cosmetic restoration and place into service on our demonstration railroad.

Track Car Training Schedule Announced


Training for train enthusiasts who wish to be Track Car Operators at the Rochester & Genesee Valley Railroad Museum, will commence in March 25 and continue through May 20, 2006.

Track Car Operator Training Schedule


Training for volunteers who wish to be Track Car Operators at either the Rochester & Gensee Valley Railroad Museum or the New York Museum of Transportation will commence in March 25 and continue through May 20, 2006.